Close your browser and change the network settings on your computer back to DHCP. During the reboot process, the Wireless Connection status will change to ACTIVE.ġ4. Click the Finish button to reflect the updated settings.ġ3. Click the Apply button to save settings.ġ2. If your wireless network is secured, choose the correct Encryption type from the dropdown menu and enter your network password. Select the desired wireless network to connect to and click Done.ġ1. The Wireless Site Survey window will open. Next, click Search to select the wireless network to connect the adapter to.ġ0.
The Ethernet-2-WiFi configuration utility will launch in your browser. Enter the following factory default User Name and Password:ĩ. Open an Internet Browser and enter 192.168.1.254 in the address bar.Ĩ. Select Ethernet in the left pane and select Manually from the Configure IPv4 dropdown menu. Connect the other end of the Ethernet cable into the Ethernet port on your MAC.Ĥ. Connect one end of the included Ethernet cable to the Ethernet-2-WiFi adapter. Start by disabling your MAC’s wireless connection.ģ. Note: Make sure to set your Ethernet device’s network connection setting to WIRED for proper operation. Use the included Ethernet cable to connect the adapter to your Ethernet enabled device such as a Blu-Ray player, HDTV or game console. Your Ethernet-2-WiFi adapter configuration is complete. During the reboot process, the Wireless Connection status will change to ACTIVE.ġ6. Click the Finish button to reflect the updated settings.ġ5. Click the Apply button to save settings.ġ4.
Select the desired wireless network to connect to and click Done.ġ3. Next, click Search to select the wireless network to connect the adapter to.ġ2. Enter the following factory default User Name and Password:ġ1. Open an Internet Browser and enter 192.168.1.254 in the address bar.ġ0. Click to highlight Internet Protocol Version 4 (TCP/IPv4) and select Properties.Ĩ.
#Iogear fokus 2 windows 10
Note: Windows 10 users need to select Network and Internet settings before arriving at Network and Sharing Center.ħ. Open Control Panel and select Network and Sharing Center. Connect the other end of the Ethernet cable into the Ethernet port on your PC.Ĥ. When complete, the WLAN LED will blink to show it’s ready to be configured.ģ. Note: It will take approximately 20 – 30 seconds to complete the boot-up sequence.
Connect the included micro-USB cable to the USB power adapter and plug into an available power outlet.Next, power on your Ethernet-2-WiFi adapter using either of the following methods: Start by disabling your PC’s wireless connection.Ģ. Use the included Ethernet cable to connect the Ethernet-2-WiFi adapter to your Ethernet enabled device such as a Blu-Ray player, HDTV or game console.After the WPS/Reset and Ethernet LED indicators turn off, the WLAN LED will begin blinking, indicating the Wireless Protected Setup is complete and has successfully connected the adapter to your wireless network.Once your router enters into WPS pairing mode, press the WPS button on the Ethernet-2-WiFi adapter within two minutes to connect the adapter to your Wi-Fi network.
#Iogear fokus 2 manual
Refer to your wireless router’s user manual for instructions to enable Wi-Fi Protected Setup.Power on your Ethernet-2-WiFi adapter by connecting the included micro-USB cable to the USB power adapter and plugging into an available power outlet.Wireless Configuration Using Wi-Fi Protected Setup (WPS) Setting Up Your Ethernet-2-WiFi Universal Wireless Adapter Blinking - Data is being transmitted or received from connected Ethernet device Blinking - WLAN is transmitting or receiving dataĪ. Blinking - The WPS feature is enabled and activeĪ. Solid - The unit is being reset to factory default settingsī. – Push and hold the reset button for 3 – 5 seconds to reset adapter to factory default settings.Ī. – Push and hold the WPS button for 3 – 5 seconds to enable the WPS feature. Wireless Router with WPS Setup or Wireless Router without WPS Setup and Ethernet enabled Computer Overview.
0 kommentar(er)
